Getting More Out of Your Sidel Combi SF300 You don’t actually need to rip out your entire oven just to get a bit more speed out of an old Sidel...

Getting Your KHS and Sidel Blow Molders Back in Sync If you’ve ever dealt with inconsistent preform temperatures, you know the headache. It...

Stop Fighting With Your PET Bottle Wall Thickness If you’re running KHS or Sidel machines, you know the frustration of uneven wall thickness....

Getting Heat Where It Actually Matters in High-Speed PET Blowing If you’re running a Krones Contiform 3 Pro or a Husky HyPET, you already know...

Getting Your Heat Right in PET Blow Molding If you’re running Sidel SBO 4/6 or KHS machines, you already know the real headache isn’t...

Getting Your Sidel Matrix Heating Just Right Here is the problem when you swap out OEM lamps in a Sidel Matrix system: the heating curve tends to...

Running a Krones Contiform line is expensive. We all know that. But it gets even worse when your OEM heating elements burn out and you’re hit...

Stop Replacing Your SIG Blomax Tubes Every Other Week If you’re constantly swapping out quartz tubes on your SIG Blomax line, you know the...

Getting the Heat Right: Sidel Matrix Infrared Lamps Here’s the deal when you’re swapping out OEM lamps in a Sidel Matrix blower: the biggest headache...

Making Your PET Blowing Machine Actually Work With Your Heaters We’ve spent a lot of time making sure our infrared lamps just work. No matter who...

Stop Fighting Your SIPA Oven: Why Your Bottles Are Coming Out Uneven If you’re running a SIPA rotary machine, you know the frustration of...

Stop Fighting With Your PET Blow Molding Lamps If you’ve ever dealt with thin walls or that annoying pearlescent haze in your preforms, you...

Getting Your Nissei ASB 150DP Back Up and Running When we built our infrared lamps for the Nissei ASB 150DP and similar PET lines, we didn’t...

A Smarter Way to Handle Your Krones Contiform Heaters Let’s be honest: keeping Krones Contiform lines running is expensive. Between the downtime and...

Getting Your PET Heating Right (Without the Headache) If your heat profile is off, your bottles are off. It’s that simple. One minute you’re...

Fixing Those Annoying Heat Spots in Your Krones Contiform 3 There’s nothing more frustrating than pulling a batch of bottles and seeing that cloudy...

Stop the Burn-outs: Better Heater Lamps for SIG Blomax Lines If you’re running SIG Blomax lines, you know the headache of tubes burning out....

Getting Your Rotary Blow Molding Heat Just Right When you’re running PET production at high speeds, you don’t have time to waste. For...

Stop Guessing With Your Sidel Matrix Heating Here is the problem when you swap out lamps in a Sidel Matrix blower: you risk messing up your...

Getting the Heat Right on Your Sidel SBO 20 Series 1 If you’ve ever swapped out OEM lamps in a Sidel Matrix or SBO 20 Series 1, you know the real...

Introduction We built these Krones heater lamps with one job in mind: to run on the Husky HyPET high-speed system. The aim is straightforward—give...

Sidel Series 2 Infrared Radiator: Heat That Actually Works for Your KHS Blow Molder Let’s cut to the chase. We built the Sidel Series 2...

Introduction Let’s talk about the Krones Contiform ceramic base lamp. It’s a direct-fit infrared heater made for PET blow molding lines....

You know the drill. The heating tunnel starts to drift, preforms come out uneven, and you spend the shift chasing temperature bands instead of making...

On the blow molding line, timing is everything. Preforms roll into the heating tunnel, and you need repeatable heat across the wall—no guesswork. If...

On the floor, seconds are money. One dead heating bulb in the blow molder and the line stops cold. Preforms start cooling unevenly. You’re...

On the plant floor, the Nissei ASB 70DP blow molder runs hard. When the infrared lamps in the heating tunnel start to drift, preform heating falls...

In the heating tunnel, that’s where the preform becomes the bottle. When an oven heater starts to sag, you see uneven wall thickness, flash,...

Out on the line, a preform heat profile that’s drifting will quietly eat your yield. Stretch ratios slip, bottles haze up, and the whole line...

On the floor, a Sidel blow molder on a PET line doesn’t sit around waiting for heating drift to show up in the bottles. When the SK15 base lamp...

On an Aoki blow molder, the heating tunnel is where you either make uptime or lose it. If the IR emitter is weak or drifts, preform heating drags...